You Should be Able to Do Custom Car Audio Installs on Your Own
Custom car audio installs can prove to be hectic at times and it is for this reason that many seek expert advise and sometimes experts to install for us our custom car audio. But when you are familiar with the guidelines, you are at a better place to master the process and eventually grasp what it takes to achieve a good custom car audio install. Firstly, a good workman must have the tools and equipment necessary. They include pliers, wire strippers, screwdrivers, wire cripper, electrical tapes and wire nuts. It is also wise to be in the proper protective clothing like work gowns and rubber gloves to make sure you are protected from all the hazards that involve the process. You can also wear goggles to protect your eyes from dust and other airborne particles.
To escape any costs that may come from removing your old system in a hurry, take your time and disconnect the wires systemically and methodically. Your new car audio will go in the same space and you need to prepare it for the new audio. Be very keen about the connectors and wires because they need to be in oder and after you are through, you can install your speaker. Connect the speakers using cables and make sure every positive and negative connections are in their right place. Follow manuals and other guides to the letter. If you are the kind of person that gets bored by too much text, there is no need to conduct a custom car audio install for yourself. Your undivided attention is the only way to produce good results.
It is wise to compare guides from one source to another. This is because you cannot be totally content with one angle. Bring variety and spice up your learning. You will discover both complex and simple steps and if something goes wrong, you know you can have different opinions to help you. Among the most asked questions in custom car audio installs are whether you have to cut wires while installing because it can easily affect your car warranty. The answer to this concern is that when you have a wiring harness with ISO connection, you can install your system directly into the wiring connector. You can also get a harness adapter to facilitate the process. An ISO connection simply means an international standard connection.
Other questions that you can get answers for are on how to fit a CD changer properly. If you have a question or even a suggestion, you can find friendly sites that will give you that information and more. To have excellent custom car audio installs really determines the quality of your car stereo sound. It is therefore a very important process to ensure you get your music the exact way you want it to be. An important aspect to read about is the caution segment. Many resources about custom car audio installs have a place where they can warn you of what not to do. You can also take in many tips that are available. Tips are generated from observed common mistakes and they know the areas where you are likely to mess up. The process is exciting and it will even be more exciting when you enjoy your favorite tunes on your system.
Help answer the question about car audio installation
What is the average price of a car audio installation?
Just a single sub, and amp.
Please include the wires in your quotes!
Thanks in advance =)
About Author
Muna Wa Wanjiru is a web administrator, For more information on Custom Car Audio Installs, visit his site at CUSTOM CAR AUDIO INSTALLSI Will Highly Appreciate Your Views About Custom Car Audio Installs On My Blog Here
Article Source: ArticlesBase.com – You Should be Able to Do Custom Car Audio Installs on Your Own
Tags: car, custom car audio install, face, free, how, install, instructions, plate, replace, stereo, system, video, wiring
car accessories | admin September 5, 2009
11 Comments to “You Should be Able to Do Custom Car Audio Installs on Your Own”
RSS feed for comments on this post. TrackBack URI
By kebruya, November 14, 2009 @ 5:11 am
Dude that is help full
By cobaltss0720, November 14, 2009 @ 5:55 am
Hey man nice, But i noticed when you armed you’re car, you’re door was open. Did you not use the door pin input? Should just diode isolate each door, then run it. so all four, or two doors will trip the alarm.
By Danny M, November 14, 2009 @ 5:58 am
You can use this website:
http://the12volt.com/
It's been very helpful to me. You can find a lot of information in the forums plus they have a listing of books you can buy. I had heard that ELAC ( East L.A. City College) had a course. I know for a fact that West Valley Occupational had one.
You can also check this site for upcoming events:
http://www.merausa.org/Events/Workshops/mera_cea_regional_workshops.asp
By breybear01, November 14, 2009 @ 2:40 pm
subs? amp? speakers? speaker amp?
what all getting done all of that ? just subs? just speakers
gimme a list and ill give you a price.
By Erik S, November 14, 2009 @ 4:22 pm
I'd charge $100 or so for that. Regardless, stay away from Circuit City, Best Buy, etc, as they take shortcuts when doing the jobs, and don't always do it right. If you are going to get it done professionally, find a local shop, or maybe even Tweeter.
By rtelmo01, November 14, 2009 @ 6:19 pm
where can i find those ‘test sheets’??…I have an Alfa Romeo 156 1.6 T.Spark…Thanks
By khan, November 15, 2009 @ 12:56 pm
circuit city will install your sub and amp for 60.99, you have to purchase the sub, amp, and wires separately..the sub can range anywhere from $40 to a few hundred dollars depending on brand and size. Same goes for an amp. A wiring kit for your amp usually costs around 70 bucks. Speaker wire is usually around .80 per foot. I just got 2 12" subs an amp and all the wiring installed. To install everything it was about 80 bucks. The subs, amp and wiring was around 750.
By chika9008, November 16, 2009 @ 6:24 am
throw him 50 bucks…if he gripes…tell him you could have gotten free installation at ABC warehouse (had you bought the unit there)…..and these days…everyone is an expert….get him a hooker and a six pak….lol
By trooper210, November 16, 2009 @ 6:36 am
do a search on MECP buy the course the basic and study it later you can go to your local library to take the test
good luck
By Bassman, November 17, 2009 @ 9:19 am
im a professional installer, i dont know where you got it installed, but wires under carpet, vaccumm floors where we worked, setting all radio settings (your old presets, clock, eq). if there is no case for the cd, then i dont put it in a case, if there is one sitting there i put it away, not all installers will, its not really a policy i dont think, just courtesy. subs dimming lights is not their fault, its from your car being weak and your system being good. unless you wanteda cap or something they did all they could. blown fuse on first day is likely going to happen if you cranked the volume trying to draw too much current through the power wire. I've never fastened a box to the car unless it was paid for as an extra and asked for specifically.
By mcr80221, November 17, 2009 @ 10:35 am
Best buy, Circut City they maybe able to help or go to mecp.com